BIENVENUE SUR NOTRE BLOGUE

Nous partageons nos connaissances dans les domaines qui nous passionnent le plus
click

Planning Factory Space And Utilities For A 45-80M Cake Line

Par Pandamachinerycn November 12th, 2026 6 vues

Introduction: A continuous cake line fits a factory only when length, width, height, service access, and utility connections are planned together as one layout.

The first number circled in a layout meeting is usually 45 m, 60 m, or 80 m, and it is also the least useful number on its own. A continuous cake line is a working corridor rather than a box: the machine train runs a set length, but it also claims width for adjacent equipment and walkways, height for overhead access, and a set of utility interfaces at fixed points along the run. Planners who mark only the length on the floor typically meet the width, height, and connection problems after the concrete is already poured. This walk-through follows the order that avoids that outcome.

Why Line Length Alone Does Not Define a Workable Layout

The published figure describes the machine train, not the room. On an industrial cake production line, the 45 m, 60 m, and 80 m options track the run of equipment from mixing and depositing through the tunnel oven, the filling station, the cooling conveyor, and the hand-off to packaging. Documentation for Panda Machinery's cake line, for instance, lists those three lengths next to a 10–20 m width and a height of about 3 m. Two of the three dimensions are already moving: length is fixed by configuration, while width shifts across a 10 m range. A layout that reserves one long, narrow rectangle has solved a third of the problem. Length also sets how many transfer points sit between machines, how far a jam can travel before anyone notices, and how much conveyor a cleaning crew has to walk. It fixes where the utility interfaces land as well: an 80 m train puts the oven several bays away from the mixing end, so the power cabinet and fuel route have to reach points that a 45 m train would place much closer together. That is why two factories can install nominally similar lines and end up with very different rooms. One practical exercise is to walk the empty floor with tape and a marker before anything is delivered. Mark the 45–80 m run first, then immediately mark the width, the operator aisle, the cleaning access side, the power cabinet footprint, the fuel route, and the compressed-air drop points. If those marks crowd each other, the room is not ready for the line at that configuration, and it costs far less to learn that on tape than after commissioning.

Which Utility Connections Shape the Layout Before Equipment Arrives

Electrical supply is the first fixed point. The line runs on 380V/220V, 50/60 Hz, three-phase power, and the oven decides how much of it is needed. An electric oven is listed at 300 kW, 600 kW, or 800 kW depending on configuration, while a gas or diesel oven is listed at 30 kW, 45 kW, or 60 kW because most of its heat comes from combustion rather than the electrical supply. That gap reshapes the room. An 800 kW electric oven pulls heavy cable runs, switchgear, and transformer capacity into the plan, and the cabinet needs a location with clearance and cable access. A gas or diesel oven moves the burden onto a fuel route instead. Fuel routing is where layout and safety planning meet. Natural gas needs a supply line running from the meter or regulator to the burner train along a path that stays out of walkways and away from ignition sources. Diesel needs storage, a fill point, and a delivery route for tankers or drums, which is a traffic question as much as a fuel question. Both routes are difficult to add later because they cross the building, not just the line. Compressed air is the third interface: the depositor and filling heads run on pneumatic actuators, so air drops are needed near those units. Air pressure and consumption values are settled during project engineering rather than printed in a standard specification table, so the practical move is to reserve a route and drop points early and size the compressor with the supplier as drawings develop. Ventilation earns the same early treatment. A tunnel oven releases heat and moisture along its length, and the extract path above the line competes for the same ceiling space as cable trays and lighting. Local engineering review and ventilation design still shape the final room, which keeps the machine envelope as a starting input rather than a finished layout.

How Width Height and Service Access Affect Continuous Flow

A continuous line earns its money by not stopping. Every unplanned stop costs more than it would on a batch oven, because product is inside the tunnel and the whole chain has to be cleared and restarted. Width, height, and service access are the three dimensions that determine how often that happens.

1. Width and Aisle Clearance Decide Whether the Line Keeps Flowing

The listed 10–20 m width is a range, and the top of it is not wasted space. The envelope has to hold the conveyor runs, control cabinets, the operator side where trays and cup feeders are loaded, and the cleaning side where crews reach food-contact surfaces between runs. EHEDG hygienic design guidance treats accessibility for cleaning as part of equipment and layout design rather than an afterthought, and commercial food manufacturing practice under FDA CGMPs assumes surfaces can be reached and cleaned on a schedule. When width is squeezed, cleaning and jam-clearing migrate into production time, and the line surrenders the continuous flow it was bought for.

2. Ceiling Height and Overhead Access Set the Pace of Maintenance

The machine stands about 3 m high, and that figure describes the equipment, not the room. Above the line sit the oven exhaust path, cable trays, air lines, lighting, and often sprinkler runs, each needing clearance from a hot oven top. Maintenance adds a second demand: filling heads, oven components, and drive units sometimes have to be lifted out vertically, and an operator needs safe footing to inspect the top of the tunnel. A room that clears the machine by a few centimetres makes routine service slow and awkward, and slow service is what turns a short stop into a long one. Service access ties the three dimensions together, because reach matters more than raw area. The depositor, the oven entry and exit, the filling heads, and the drive units each need a standing position, and the aisle serving one may not serve another. Planning access as a walking route along the whole line, rather than as leftover gaps, is what keeps a long machine serviceable. Machinery safety reviews, including the CE conformity work described for equipment sold in the EU, treat access and guarding as design inputs rather than installation details.

Conclusion

None of this makes 45, 60, or 80 m the wrong place to start; it makes length a starting input. A workable layout stacks that run against a 10–20 m width, a height that clears ducts and vertical lifts, service routes reaching every unit, and utility interfaces for three-phase power, fuel, and compressed air marked on the floor before equipment arrives. The sequence matters: reserve the routes and the access, then place the machine train inside them. A cake production line supplier can usually provide dimension and utility interface drawings early enough to plan around, and requesting them first avoids the expensive version of this conversation.

FAQ

Q: Why is a 45–80 m cake line layout not decided by length alone?

A: Length tells you how much machine train you have to house, not how much room the line needs. The documented configurations run 45, 60, or 80 m long, but the same documentation gives a 10–20 m width and roughly 3 m of machine height, and the layout also has to absorb walkways, cleaning access, control cabinets, a fuel route, and compressed-air drop points. A plan built on the length figure alone usually gets redrawn once width and access requirements appear.

Q: Which utilities need to be understood before a continuous cake line is placed?

A: Start with the electrical supply: 380V/220V, 50/60 Hz, three-phase, sized around the oven, which is listed at 300/600/800 kW for electric heating or 30/45/60 kW for gas or diesel heating. Then confirm the fuel route, either a gas line to the burner train or diesel storage with a fill point. Compressed air feeds the depositor and filling pneumatics, so reserve a route and drop points and size pressure and consumption later with the supplier, alongside ventilation space above the oven.

Q: How do width, height, and service access affect a cake production line layout?

A: Width decides whether there are real walkways on the operator and cleaning sides, which is what lets the line be cleaned and cleared without stopping production. Height has to clear not only the roughly 3 m machine but the exhaust path, cable trays, and any vertical lift needed for maintenance. Service access decides how quickly the line restarts after a stop, because a filling head or oven component reachable only from one cramped side turns routine service into a long shutdown.

Sources / References

EHEDG Guideline Catalogue

Current Good Manufacturing Practices (CGMPs) for Food and Dietary Supplements | FDA

Machinery – Internal Market, Industry, Entrepreneurship and SMEs

Related Examples

Full Automatic Cake Production Line-Panda Machinery 
La page précédente
Batter Aeration And Density Control In Continuous Cake Production
En savoir plus
Leave a message
Name *
Email *
Country
Tel
WhatsApp
Message *
Nous utilisons des Cookie pour améliorer votre expérience en ligne. En poursuivant votre navigation sur ce site, nous supposons que vous acceptez notre utilisation des Cookie.